JASO M101 PDF

Scope This standard specifies the steel for automotive structurai uses hereinafter referred to as "steel". The steel specified here includes the hot rolled steel and the cold finished steel processed such a secondary operation as "drawing". Remark: Attached table 1 shows applicable standards of this standard. Classifications and designations Classifications and designations of the steel shaii conform to those in Table 1. The permissible deviation shall be determined as agreed upon between the purchaser and the manufacturer. S30C, S33C.

Author:JoJokinos Gam
Country:Turks & Caicos Islands
Language:English (Spanish)
Genre:Finance
Published (Last):26 April 2017
Pages:269
PDF File Size:18.15 Mb
ePub File Size:6.26 Mb
ISBN:136-6-27375-864-6
Downloads:54848
Price:Free* [*Free Regsitration Required]
Uploader:Tojaramar



Dikasa The pipes shall be tested pursuant to Table 10 and shall resist the guarantee pressure specified in Table m without leaving injurious deformation. Designation of products shall be pursuant to the standard number, type of tubing, and type and nominal diameter of outside surface. Inspection shall be conducted pursuant to the above 6 and the results shall meet requirements specified in the above 4. The test shall be conducted pursuant to corrosion test specified in Table 10 and shall meet requirements in Table 6.

The welded low carbon steel pipes shall be made by copper coating both surfaces or inner surface of SPCC specified in JIS Gshaping them into a tubular form, and sealing the edges by electric resistance welding, however inside surface, may not be copper coated if mutually agreed upon by the purchaser and the manufacturer.

When the plates are pressed, the weld of tube shall be placed at 90 degrees to the direction of applied force. The brazed double wall low carbon steel pipes shall be made by copper-coating both surfaces of SPCC specified in JIS G, shaping them into the form of double wall tubing, and sealing the seams by copper brazing and fusion in a reduction furnace.

Standards automobile tubingJASOmetal pipestube standard. Flattening Test 1 Length of test specimen shall be mm. Copper and copper alloy seamless pipes and tubes C or C Tubing mainly for air brakes 2. Examine if any leak of other defects occurred or not when pipe is applied with specified hydraulic pressure and held for 5 minutes. Inspection shall be conducted by the above 6 and the results shall meet requirements m01 in the above 3. Iron rust red rust shall appear 5 spots or less per 50 cm 2 in 24 hours.

Performance of organic film shall be pursuant to Table 6 and shall meet requirements in Table 7, after the tests pursuant to Table 10 are conducted as occasion demands. Method of manufacturing 4. Example if any flaws, cracks, or other m occurred or not when the pipe was bent degrees around a cylinder having the radius as specified below.

TOP Related Articles.

ANATOMIE ARTISTICA GHEORGHE GHITESCU PDF

自動車JASO M 101-94のための二重/単一の壁の精密鋼鉄管

Gugal Inspection shall be conducted pursuant to the above 6 and the results shall meet requirements specified in the above 4. Copper and copper alloy seamless pipes haso tubes C or C Tubing mainly for air brakes 2. The welded low carbon steel pipes shall be made by copper coating both surfaces or inner surface of Jaos specified in JIS Gshaping them into a tubular form, and sealing the edges by electric resistance welding, however inside surface, may not be copper jado if mutually agreed upon by the purchaser and the manufacturer. When jasl plates are pressed, the weld of tube shall be placed at 90 degrees to the direction of applied force. The pipes shall be tested pursuant to Table 10 and shall resist the guarantee pressure specified in Table 8 without leaving injurious deformation. Example if any flaws, cracks, or other defects occurred or not when the pipe was bent degrees around a cylinder having the radius as specified below.

CANNE HEXAGRAPH PDF

JASO M101 PDF

Yole Examine if any leak of other defects occurred or not when pipe is applied with specified hydraulic pressure and held for 5 minutes. When the plates are pressed, the weld of tube shall be placed at 90 degrees to the direction of applied force. The pipes shall be tested pursuant to Table 10 and shall resist the guarantee jqso specified in Table 8 without leaving injurious deformation. The welded low carbon steel pipes shall be made by copper coating both surfaces or inner surface of SPCC specified in JIS Gshaping them into a tubular form, and sealing the edges by electric resistance welding, however inside surface, may not be copper coated if mutually agreed upon by the purchaser and the manufacturer. Pursuant to JIS H Guarantee pressure test Examine if any leak of other defects occurred or not when pipe is applied with specified hydraulic pressure and held for 5 minutes. Standards automobile tubingJASOmetal pipestube standard. Flattening Test 1 Length of test specimen shall be mm.

Related Articles