EV CPS2.9 PDF

Vudorn Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat radiating devices. In DUAL mode, the two channels of the power amplifier work independent from each other. Make sure to completely read and fully observe power rating specifications of the speaker systems to be used and to check them against the output power capacity of the power amp. As with all Electro-Voice power amps with fan cooling, the airflow direction is front-to-rear, obviously because there is more cold air outside of the rack case than inside.

Author:Kajihn Faegami
Country:Denmark
Language:English (Spanish)
Genre:Medical
Published (Last):21 December 2006
Pages:297
PDF File Size:1.9 Mb
ePub File Size:10.7 Mb
ISBN:467-9-14609-308-5
Downloads:86841
Price:Free* [*Free Regsitration Required]
Uploader:Daizahn



Vudorn Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat radiating devices. In DUAL mode, the two channels of the power amplifier work independent from each other. Make sure to completely read and fully observe power rating specifications of the speaker systems to be used and to check them against the output power capacity of the power amp.

As with all Electro-Voice power amps with fan cooling, the airflow direction is front-to-rear, obviously because there is more cold air outside of the rack case than inside. Whenever possible, using balanced audio signal feeds ve the input of the power amplifier is always preferred.

Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat radiating devices. The power amplifier remains cooler and dissipating the developing waste heat in a specific direction gets easier. A soft start circuit compensates mains inrush current peaks and thus prevents triggering AC mains fuse when switching on the amplifier. Introduction 1 Introduction 1. This manual also for: Level Indicators for channels 1 and 2 2.

Additionally securing the amplifier at the rear becomes necessary, if the rack case in which the power amplifier has been installed will be transported. This indicates all protections are working fine. Mains Switch Rear View 1.

Only the provided power cord may be used. Unbalanced connections should cp2. CPS 2. Whenever possible, using balanced audio signal feeds at the input of the power amplifier is always preferred. Attach the power amp with its frontal rack mount ears using 4 screws and washers as shown in following illustration. The correct connection is also indicated at the amplifiers rear panel. Electro-Voice CPS2. Electrovoice contractor precision cps2t: Keep ventilation louvers free from dust to ensure unhindered airflow.

F reserved Table 4. The Mains Switch on the front panel separates the power amp from the mains. Unbalanced connections should only be used if the cables are very short and no interfering signals are to be expected in the vicinity of the power amplifier. PARALLEL operation is the mode of choice, whenever the same input signal drives multiple power amp channels of a large system installation. The difference between power consumption and dispensed power is called power dissipation P d.

Otherwise, a 6 dB drop in level could cpa2. Due to their immunity against external interference sources, such as dimmers, mains connections, HF-control lines, etc. The ground lift switch allows eliminating noise loops. Controls, Indicators and Connections Front View 1. CPS amplifiers have been designed for installation in a conventional inch rack case. Comments to this Manuals Your Name. Do not modify this unit! Set the switch to the 50 Hz position for activating the High Pass Filter. The power drawn from the mains network is converted into output power to feed the connected loudspeaker systems and into heat.

Electrovoice compact precision cps: Most 10 Related.

BHANUMATI KA PITTARD PDF

เพาเวอร์แอมป์ EV CPS2.9 Power Amplifier

Mauzil Following table shows possible switch settings and corresponding delay times. Controls, Indicators and Connections Front View 1. Unbalanced connections should only be used if the cables are very short and no interfering signals are to be expected in the vicinity of the power amplifier. Mains Switch Rear View 1. The power drawn from the mains network is converted into output power to feed the connected loudspeaker systems and into heat.

AVANUKKU NAAN AZHAGU NOVEL PDF

Electro-Voice CPS 2.9

Duk Turning the control to the right dv and turning it to dv left decreases the volume. Keep ventilation louvers free from dust to ensure unhindered airflow. Attach the power amp with its frontal rack mount ears using 4 screws and washers as shown in following illustration. Keep ventilati- on louvers free from dust to ensure unhindered airflow. This mode of operation is being used for all 2-channel applications, like stereo operation. Show all Contractor precision cps2.

EL PROCESO DE MACANAZ PDF

Electro-Voice ELETRO-VOICE CPS2.12 Owner's Manual

.

Related Articles